HomeCalcs

Drywall Calculator

Enter your room size and sheet size to get a shopping list of drywall sheets, screws and joint compound.

Drywall · sheets, screws & mud

—

Joint compound coverage is printed on the bucket or box. Sheet sizes and thicknesses are on the stack label at the store.

How the calculator works

The calculator adds up the wall area (the room perimeter times the ceiling height), subtracts the doors and windows you enter, and adds the ceiling if you choose it. That gives the area you actually need to cover.

To get sheets, it adds your waste allowance and divides by the area of one sheet, then rounds up to a whole sheet, because you cannot buy part of one. A rectangular room with few openings usually needs about 10 percent extra for cuts and mistakes. Rooms with many corners, angles or short walls often need more.

Screws are estimated from the total sheet area you are buying, at a typical spacing for walls and ceilings of roughly one screw per square foot with a little extra. Joint compound uses the finished area, without the waste allowance, divided by the coverage figure you enter. Joint compound is rounded up to whole gallons (or liters).

Common drywall sizes and thicknesses

ItemTypical use
4 x 8 ft sheet (32 sq ft)Easiest to carry and handle; the usual choice for most rooms and for DIY
4 x 9 ft or 4 x 10 ft sheetTaller walls, fewer horizontal seams to finish
4 x 12 ft sheetLong walls and ceilings; fewer seams but heavy and awkward for one person
1/2 inch thickStandard for walls in most homes
5/8 inch thickCeilings, fire-rated walls and garage walls; stiffer and less likely to sag
1/4 inch or 3/8 inch thickCurved walls, overlays and some repairs

A worked example

Here is how the numbers work out for a typical bedroom where only the walls are being covered.

Room length
14 ft
Room width
12 ft
Ceiling height
8 ft
Doors and windows (total area to subtract)
40 sq ft
Include the ceiling?
No, walls only
Sheet size
4 x 8 ft (1.22 x 2.44 m)
Waste and cutting allowance
10 %
Joint compound coverage (check your label)
100 sq ft per gallon
Result
13 drywall sheets
Also
500 drywall screws
Also
4 gallons of joint compound

How to measure your room

Measure the length and width of the room at floor level and use the full dimensions, even if there are small alcoves. If a room is not a simple rectangle, run the calculator once for each rectangular part and add the results together.

For openings, add up the area of doors and windows, using width times height for each. Many installers only subtract openings larger than about a small closet door, because the cut-out pieces rarely get reused. If your room has just a couple of small windows, you can enter a low number or zero to stay on the safe side.

Screws, tape and joint compound

Screws are sold by weight or by the box, so check the count on the package and divide the number here by it. Use drywall screws long enough to go through the board and well into the framing. The length depends on the sheet thickness, so check the screw box.

Joint compound coverage depends on the type: premixed all-purpose, lightweight and setting-type compounds all cover differently, and it also depends on how many coats you apply and how smooth you want the finish. Use the coverage printed on your product and change the figure above.

Remember the extras that are not in the calculator. You will also need paper or mesh tape for the seams, corner bead for outside corners, and sandpaper or sanding sponges.

Choosing sheet size and layout

Longer sheets mean fewer joints to tape and sand, but they are heavy and hard to get through doors and up stairs. For most home projects, 4 x 8 ft sheets are the practical choice. If your ceiling is taller than 8 ft, taller sheets or a second row may be needed.

Plan seams so they land on framing, avoid the corners of doors and windows, and stagger joints between rows. Hang the ceiling first and the walls after, so wall sheets help hold the ceiling edges in place.

How much waste to allow

A plain room with few openings often needs only a modest allowance. Add more if you have lots of cutouts, angled walls, stairwells or vaulted ceilings, or if this is your first time hanging drywall.

It is much better to have one sheet left over than to be one sheet short, because a second trip costs time and the new sheets may come from a different batch. Leftover boards are handy for repairs.

Frequently asked questions

How many sheets of drywall do I need for a room?

It depends on the wall area, whether you are doing the ceiling, how many doors and windows there are, and the size of the sheets. Enter your room dimensions above and the calculator adds a waste allowance and rounds up to whole sheets.

Should I subtract doors and windows?

You can, and the calculator does it for you. For small openings the savings are minor, and many installers do not subtract them so they have spare board for cuts. Subtract large openings, such as wide windows and garage-style doors, to avoid overbuying.

How much joint compound do I need?

Check the coverage on your product label, as it varies by type and by how many coats you apply. Typical coverage is often around 80 to 120 sq ft per gallon for a full finish, but use the number from your own product.

Is 1/2 inch or 5/8 inch drywall better?

Half-inch is the standard for most walls. Five-eighths inch is stiffer and often used on ceilings, where it resists sagging, and wherever fire-rated assemblies are required. Check your local building code if you are unsure.

Do the sheets need to be installed horizontally or vertically?

Horizontal hanging, with the long edge across the studs, is common on walls because it reduces the length of seams and gives a stronger wall. Vertical hanging is also used, especially when the wall height matches the sheet length. Both can work if the edges land on framing.

More calculators